Skip to content

Tidy Brush

Tidy Brush cleans up an AI-generated model, often right after Polyreduce. It smooths away the little pinched folds, dents and bumps a few triangles wide that read as damage, while the model keeps its size and its larger features such as a nose or a knuckle. It can also thin out needless triangles: long thin slivers and fans of tiny triangles. Clean the whole mesh, or only a selection.

Mesh

The mesh to clean up, typically an imported AI model after Polyreduce.

Mesh

The same mesh with its small folds, dents and bumps smoothed away and, with Simplify, its needless triangles thinned.

Parameter What it does Default
Strokes Brush strokes painted on the mesh in the viewport. None (paint in the viewport)
Apply to Where the cleanup may happen: Everywhere, or a named selection. Invert flips the choice. Everywhere
Smooth everywhere How much to smooth away folds, dents and bumps, everywhere Apply to allows. 1 is fully smoothed; the shape keeps its size. 0
Keep sharp edges Keeps hard edges sharp (a belt rim, an armor plate edge) while the surface around them smooths. Off
Sharper than How sharp an edge must be to keep it: the angle its two faces turn by. Shown when Keep sharp edges is On. 60
Simplify everywhere How much to thin needless triangles (slivers, fans), everywhere Apply to allows. Flat areas thin out; curved ones resist. 0
Max simplify error How far Simplify may move the surface where its amount is 1. Larger thins more. 1 cm

Select the node and the viewport turns into a brush. A ring shows where it lands and how big it is.

  • Hold the left mouse button on a fold, dent or patch of cluttered triangles. The longer you hold, or the slower you pass, the more it cleans up there.
  • Ctrl + drag erases: it takes the cleanup back where you paint, at once.
  • The bar at the bottom of the viewport picks what the brush does (Smooth, Simplify or Both), its Strength (how fast holding still cleans up; 0.5 takes two seconds to clean up fully) and its Radius. The trash button clears every stroke.
  • [ and ] shrink and grow the ring; Shift + mouse wheel changes Strength. With a pen, pressing harder paints stronger.
  • X symmetry (on by default) paints the mirror image across the middle of the model too, so one stroke fixes both legs. Turning it off later keeps what was already painted on both sides.
  • While the brush is up, a heat overlay shows what you painted: blue where it smooths, orange where it simplifies, stronger where it is more opaque. It follows the brush right away; the mesh itself catches up a moment later.
  • Ctrl + Z undoes the last stroke (or a Clear); Ctrl + Shift + Z redoes it.
  • Strokes are stored where you painted them on the surface, not by vertex number, so they stay in place when you change the mesh upstream, for example a different Polyreduce target.
  • The brush works inside a subnet too, once you dive in.
  • Painting needs the node’s input to be a mesh. Click empty space to orbit as usual; Alt + drag always orbits.
  • Smooth everywhere sets how much to correct across the whole mesh, from 0 (untouched, the default) to 1 (fully smoothed). Lower values correct less. Brushed strokes add to it where you painted.
  • The shape keeps its size. The smoothing lifts a dent back out into the surface around it, so smoothing an arm all the way doesn’t make it thinner.
  • Textures stay put. Points move in and out of the surface, never along it, so a mesh that is already unwrapped and painted keeps its texture where it was. Use it before or after Auto Unwrap and Bake.
  • Open edges smooth only along the edge, so a hole doesn’t shrink. Sharp corners of an edge stay where they are.
  • Keep sharp edges is for hard-surface parts: an edge sharper than the angle you set straightens but stays sharp. Leave it off on organic models, where the creases are usually the defects.
  • Smoothing adds and removes nothing. With Simplify at 0, the mesh comes out with the same vertices and faces.
  • Simplify everywhere sets how much to thin needless triangles, from 0 (untouched, the default) to 1. It runs after the smoothing.
  • Slivers turn first. A long thin triangle pair swaps to its better diagonal where the surface is flat enough, which moves nothing.
  • Then needless triangles merge away, as long as the surface stays within Max simplify error of where it was (1 cm by default, less where Simplify is below 1). Flat areas thin out; curved areas resist, so a silhouette keeps its shape.
  • Seams are never crossed. A point on a UV seam, a material border, a hard edge or an open edge stays, so textures stay exactly where they were.
  • The triangle count only goes down. Where it changes the triangles, the faces come out as triangles (as after Polyreduce), and point and edge selections are dropped with a warning.

To clean up only part of the model, make a Selection first and pick it in Apply to. The smoothing fades out over two rings of triangles around it, so the cleaned patch blends into the rest.

  • Polyreduce: lower the triangle count first.
  • Clean: repair cracks and floating fragments of an import.
  • Topology nodes: the other nodes that change the polygon count or layout.